Доступно к заказу
Цена по запросу
Гарантия лучше цены
Предложим наиболее выгодную цену на данный товар
High efficiency stainless steel filters for the treatment of biogas from anaerobic digesters and landfills for flow rates of up to 1110m³/h and a maximum operating pressure of 0.5 bar g.
Полное описание продукта
Biogas produced in anaerobic digesters and landfills is saturated with water and contains foams, small solid particles in suspension, greases, particulates and other contaminants: it is therefore essential that these contaminants are removed from the gas by filtration prior to any downstream equipment or pipework.Failure to remove these impurities may lead to a malfunction of devices and processes downstream and, in the absence of effective dehumidification, can cause clogging or blocking of blowers, heat exchangers and gas meters increasing maintenance costs and plant down time.
Hyperfilter BioEnergy filters have been specifically designed to prevent these undesired effects, available in a range of sizes matched to the needs of biogas applications. The secret of Hyperfilter BioEnergy is its highly advanced filter element. This combines ultra-high particle retention efficiency with extremely low pressure drop which results in clean, ready to use biogas with service costs kept to a minimum.
Features
• High efficiency filtration media
• Stainless steel housing materials (AISI304 or AISI316L) with pickling and passivation treatment
• Range of sizes to cover biogas flow rates from 105 to 110 m³/h (larger sizes available on request)
• Supplied complete with support legs for easy installation and mounting
• Top access cover to enable quick and easy element replacement
Benefits
• Maximum protection for downstream equipment and pipework significantly reducing maintenance costs and plant downtime
• Highly reliable and continuous operation even in the harshest conditions typically experienced in a biogas plant or landfill
• Very low pressure drop
Sizing and Selection
Important Note: For quoted gas purity performance, gas filters must be sized correctly for minimum operating pressure and maximum inlet flow rate using the correction factors found in the Product Information Sheet.
For more information or a detailed discussion about your specific requirements please contact Parker or an authorised Parker distributor.
Характеристики
| Размер выпускного порта: | DN80 to DN300 |
| Максимальное рабочее давление: | 0.5 barg, 7.25 psig |
| Вес: | 32 to 108 kg, 70.55 to 238.10 lb |
| Ширина: | 440 to 633 mm, 17.32 to 24.92 inch |
| Высота: | 1454 to 1883 mm, 57.24 to 74.13 inch |
| Тип соединения: | Flanged DIN EN 1092-1 |
| Максимальный расход: | 61.80 to 653.33 CFM |
| Номинальное значение в микронах: | 20 μm |
| Показатель эффективности фильтра: | 100% |
| Максимальная рабочая температура: | 100 °C, 212 °F |
| Минимальная рабочая температура: | -10 °C, 14 °F |
| Совместимый элемент: | EL-FFB105-265 or EL-FFB720-110 |
| Бренд: | Parker Hiross |
| Соблюдены требования технических условий: | not necessary due to low pressure |
| Применение: | Filtration of biogas |
| Интервал между заменами элемента: | 6 months |
| Количество элементов: | 1 |
Характеристики
- Бренд
- Parker Hiross
- Вес
- 32 to 108 kg, 70.55 to 238.10 lb
- Высота
- 1454 to 1883 mm, 57.24 to 74.13 inch
- Интервал между заменами элемента
- 6 months
- Количество элементов
- 1
- Максимальная рабочая температура
- 100 °C, 212 °F
- Максимальное рабочее давление
- 0.5 barg, 7.25 psig
- Максимальный расход
- 61.80 to 653.33 CFM
- Минимальная рабочая температура
- -10 °C, 14 °F
- Номинальное значение в микронах
- 20 μm
- Показатель эффективности фильтра
- 100%
- Применение
- Filtration of biogas
- Размер выпускного порта
- DN80 to DN300
- Соблюдены требования технических условий
- not necessary due to low pressure
- Совместимый элемент
- EL-FFB105-265 or EL-FFB720-110
- Тип соединения
- Flanged DIN EN 1092-1
- Ширина
- 440 to 633 mm, 17.32 to 24.92 inch
Нет отзывов об этом товаре.